We are an independent international distributorship for HeatFlexx
INSTRUCTIONS FOR WIPER INSTALLATION KIT
EASY INSTALLATION! Just plug it in.
Parts included: (1) Wiper wiring harness, (1) Cigarette lighter adapter, (1) Direct connect wire, (1) Extension cord, (2) Replacement fuses, (4) Zip ties.
1. Installation using ‘cigarette lighter adapter’ (Easy Installation)
- Option A: (Through Drivers Door)
- Take the wire with two (2) male and one (1) female connector and attach the two male ends to wiper blades. Use zip ties provided to secure wires to wiper arms.
- Open the hood and run the wire (female connector) under the hood toward the driver’s side fender. Feed wire under the fender toward the door jamb (between the fender and the door frame).
- From inside the door jamb, pull back the door’s rubber seal and run the wire behind the seal and re-insert the seal.
- Connect the wire with the cigarette lighter adapter attached. Note: If required, an extension cord has been provided to add more length.
- Run the wire under the dash (use a twist tie to secure wire if required)
- Plug in cigarette lighter adapter to activate heating element in wipers. (Note: Wipers are equipped with a thermostatic sensor and will only activate when the temperature is below 40°F / 4°C).
- Option B: (Through Firewall)
- Take the wire with two (2) male and one (1) female connector and attach the two male ends to wiper blades. Use zip ties provided to secure wires to wiper arms.
- Open hood of vehicle and feed the wire (female connector) down through a hole / plug in the firewall (I.e. Look for rubber grommet on firewall or feed wire through the existing wiring harness that passes through firewall). Note: If required, an extension cord has been provided.
- From inside the vehicle, connect the wire with cigarette lighter adapter attached, to the female connector coming in through the firewall.
- Plug in cigarette lighter adapter to activate heating element in wipers. (Note: wiper s are equipped with a thermostatic sensor and will only activate when the temperature is below 40°F / 4°C).
- 1. Take the wire with two (2) male and one (1) female connector and attach male ends to wiper blades. Use zip ties provided to secure wires to wiper arms.
- 2. Open hood of vehicle and connect the female end to the male connector on the ‘direct connect’ wire. (This is the wire with red and black wires exposed).
- 3. Connect red wire (+ positive) to a positive (+) ‘keyed’ power source (any power feed that only has power when the key is in the on position and likewise no power when the key is in the off position). Next, connect the black wire to a negative (-) ground. (Note: Do not connect to battery or alternator)
- 4. Heating element in wipers will activate when key is turned ‘on’. (Note: wipers are equipped with a thermostatic sensor and will only activate when the temperature is below 40°F / 4°C).
ATTENTION
ALL “ADD TO CART” WIPER ORDERS MUST INCLUDE 1 WIRING KIT WITH EACH PAIR OF BLADES!!!!!
“ADD TO CART” ORDERS THAT DO NOT INCLUDE A WIRING KIT WITH EACH PAIR OF BLADES WILL BE REJECTED AND PAYMENT REFUNDED.
PLEASE NOTE: YOU ARE ORDERING SINGLE BLADES, NOT PAIRS OF BLADES IN YOUR SHOPPING CART.
REPEAT CUSTOMERS THAT REQUIRE ONLY BLADES, PLEASE E-MAIL YOUR REQUEST.
For shipping in North America please use the Shopping Cart below.
For outside of North America AND Repeat Customers You MUST E-mail your request to cdnbvr@gmail.com
PLEASE NOTE:
YOU ARE ORDERING SINGLE BLADES, NOT PAIRS OF BLADES IN YOUR SHOPPING CART.
Wiring Kits
1: Measure the length of each wiper blade.
(Some cars have a different size on drivers side from passenger side.)
2: E-mail your name, address, phone number, blade sizes, number of wiper blades and wiring kits to cdnbvr@gmail.com.
3: We will have PAY PAL send you a payment request. When you have made payment,
we will send you the wipers.
Orders will be sent out by next business day.
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |